| 編號 | 中文名稱 | 英文名稱 |
|---|
| DIN 267-13-2007 | 緊固件.技術規范.第13部分:在-200℃～700℃溫度范圍使用的具有特殊機械性能螺栓連接件用部件 | Fasteners - Technical specifications - Part 13: Parts for bolted connections with specific mechanical properties for use at temperatures ranging from -200 °C to +700 °C |
| DIN 267-2-1984 | 緊固件.交貨技術條件.結構和尺寸精度 | Fasteners; technical delivery conditions; design and dimensional accuracy |
| DIN 267-24-2007 | 緊固件.交貨技術條件.第24部分:不帶規定驗證載荷值的螺母用硬度等級 | Fasteners - Technical delivery conditions - Part 24: Hardness classes for nuts without specified proof load values |
| DIN 267-26-2005 | 緊固件.技術規范.第26部分:螺栓連接件用錐形彈簧墊圈 | Fasteners - Technical specifications - Part 26: Conical spring washers for bolted connections |
| DIN 267-27-2004 | 緊固件.帶粘附層的鋼制螺釘、螺栓和螺柱技術規范 | Fasteners - Part 27: Steel screws, bolts and studs with adhesive coating, Technical specifications |
| DIN 267-28-2004 | 緊固件.第28部分:帶壓緊層的鋼制螺釘、螺栓和螺柱.技術規范 | Fasteners - Part 28: Steel screws, bolts and studs with locking coating; Technical specifications |
| DIN 267-29-1993 | 緊固件.在-200℃～+700℃溫度范圍使用的螺栓連接件的產品等級 | Fasteners; product grades for parts for bolted connections for use at temperatures ranging from -200 °C to +700 °C |
| DIN 267-30-2001 | 緊固件.交貨技術條件.第30部分:特性等級為10.9的米制滾絲螺釘 | Fasteners - Technical delivery conditions - Part 30: Metric thread rolling screws of property class 10.9 |
| DIN 267-6-1975 | 緊固件和類似零件.產品等級F的表面粗糙度和公差技術規范 | Fasteners and similar parts; technical specifications, finishes and tolerances for product grade F |
| DIN 29895-1984 | 航空和航天.可選擇的緊固件材料 | Aerospace; alternative materials for fasteners |
| DIN 29895-2-1989 | 航空航天.可選擇的緊固件材料.第2部分:實心鉚釘 | Aerospace; alternative materials for fasteners; solid rivets |
| DIN 3132-1984 | 肘節式緊固件.帶短支撐板的凸出部 | Toggle-type fasteners; salient, with short base plate |
| DIN 3133-1984 | 肘節式緊固件.帶加長支撐板的凸出部 | Toggle-type fasteners; salient; with elongated base plate |
| DIN 3134-1984 | 肘節式緊固件.帶和不帶鎖緊孔 | Toggle-type fasteners; with and without locking eye |
| DIN 34804-2002 | 緊固件.黑色表面的外觀變化 | Fasteners - Change of appearance of black surfaces |
| DIN 4000-160-2007 | 產品性能制表規劃.第160部分:帶內螺紋緊固件 | Tabular layout of product properties - Part 160: Fasteners with external thread |
| DIN 4000-161-2007 | 產品性能制表規劃.第160部分:帶外螺紋緊固件 | Tabular layout of product properties - Part 161: Fasteners with internal thread |
| DIN 43835-1971 | 指示儀表的固定.緊固件、殼體錐鉚釘、安裝配置 | Fastening for indicating instruments; fastening component, cone-rivets at the case, mounting arrangement |
| DIN 48069-1-1977 | 架空電力線用無保護緊固件的雙眼 | Double eyes without protective fitting attachment, for overhead power lines |
| DIN 65151-2002 | 航空航天系列.橫向負載條件下緊固件的鎖定特性的動態試驗(振動試驗) | Aerospace series - Dynamic testing of the locking characteristics of fasteners under transverse loading conditions (vibration test) |
| DIN 65428-1987 | 航空航天.帶凸頭的緊固件用壁厚為0.25mm的襯套 | Aerospace; sleeves; wall thickness 0,25 mm, for fasteners with protruding head |
| DIN 65429-2002 | 航空航天.凸頭緊固件用壁厚為0.5mm的套筒 | Aerospace - Sleeves, wall thickness 0,5 mm, for fasteners with protruding head |
| DIN 65430-2002 | 航空航天.埋頭緊固件用壁厚為0.25mm的套筒 | Aerospace - Sleeves, wall thickness 0,25 mm, for fasteners with countersunk head |
| DIN 65431-2002 | 航空航天.埋頭緊固件用壁厚為0.5mm的套筒 | Aerospace - Sleeves, wall thickness 0,5 mm, for fasteners with countersunk head |
| DIN 65433-2002 | 航空航天.帶減徑埋頭的緊固件用壁厚為0.25mm套筒 | Aerospace - Sleeves, wall thickness 0,25 mm, for fasteners with reduced countersunk head |
| DIN 65434-1987 | 航空航天.小埋頭緊固件用壁厚為0.5mm的襯套 | Aerospace; sleeves; wall thickness 0,5 mm, for fasteners with reduced countersunk head |
| DIN 65435-1989 | 航空航天.緊固件用襯套.技術規范 | Aerospace; sleeves for fasteners; technical specification |
| DIN 65485-1993 | 航空航天.結構用緊固件.旋轉的緊固件的機械特性.旋轉的緊固件總成 | Aerospace; fasteners for structural application; rotary fastener, mechanical properties; rotary fastener, assembly |
| DIN 65486-1993 | 航空航天.結構用緊固件.旋轉緊固件的機械特性.壓力密封型緊固件總成 | Aerospace; fasteners for structural application; rotary fasteners, mechanical properties; rotary fastener, assembly, pressure-tight |
| DIN 65487-1993 | 航空航天.結構用緊固件.旋轉緊固件.沉頭螺樁 | Aerospace; fasteners for structural application; rotary fasteners; stud with countersunk head |
| DIN 65488-1993 | 航空航天.結構用緊固件.旋轉緊固件.安裝尺寸 | Aerospace; fasteners for structural application; rotary fasteners; installation dimensions |
| DIN 65489-1993 | 航空航天.結構和非結構用緊固件.旋轉緊固件.沉頭墊圈 | Aerospace; fasteners for structural and non-structural applications; rotary fasteners; countersunk washer |
| DIN 65492-1993 | 航空航天.結構緊固件.旋轉緊固件.緊固件插孔 | Aerospace; fasteners for structural application; rotary fasteners; receptacle |
| DIN 65493-1993 | 航空航天.結構緊固件.旋轉緊固件.壓力密封式緊固件插孔 | Aerospace; fasteners for structural application; rotary fasteners; receptacle, pressure-tight |
| DIN 68163-1982 | 裝配木托盤的緊固件.釘子 | Fasteners for assembling timber pallets; nails |
| DIN 6885-1-1968 | 無錐形作用的傳動型緊固件.平行鍵、鍵槽、深度型式 | Drive Type Fastenings without Taper Action; Parallel Keys, Keyways, Deep Pattern |
| DIN 6885-2-1967 | 無錐形作用的傳動型緊固件.機床用平行鍵、鍵槽、深度型式.尺寸和用途 | Drive Type Fastenings without Taper Action; Parallel Keys, Keyways, Deep Pattern for Machine Tools, Dimensions and Application |
| DIN 6885-3-1956 | 無錐體作用的驅動式緊固件.淺插入型直銷鍵.尺寸和用途 | Drive Type Fastenings without Taper Action; Parallel Keys, Shallow Pattern, Dimensions and Application |
| DIN 6886-1967 | 錐度驅動應力型緊固件.斜鍵、鍵槽、尺寸和應用 | Stressed-type Fastenings with Taper Action; Taper Keys, Keyways, Dimensions and Application |
| DIN 6887-1968 | 錐度驅動應力型緊固件.彎頭斜鍵、鍵槽、尺寸和應用 | Stressed-type Fastenings with Taper Action; Taper Keys with Gip Head, Keyways, Dimensions and Application |
| DIN 6888-1956 | 不帶鍵錐度的傳動式緊固件.半圓鍵.尺寸和應用 | Drive Type Fastenings without Taper Action; Woodruff Keys, Dimensions and Application |
| DIN 6892-1998 | 無錐度連接的驅動式緊固件.直行鍵.計算和設計 | Drive type fastenings without taper action - Parallel keys - Calculation and design |
| DIN 74361-2-1982 | 汽車和掛車的盤式車輪.柱螺栓定心的緊固件 | Disc wheels for motor vehicles and trailers; fasteners for stud centring |
| DIN 74361-3-1979 | 汽車和掛車用輻板式車輪.第3部分:輪轂孔定心附件用尺寸和緊固件 | Disc wheels for motor vehicles and trailers; dimensions and fasteners for attachment with centring on wheel bore |
| DIN 918 Bb.3-2005 | 緊固件.歐洲標準.綜述 | Fasteners - European Standards - Survey |
| DIN 918-1979 | 緊固件.術語.術語的拼寫.縮寫 | Fasteners; Terminology; Spelling of terms; Abbreviations |
| DIN 969-1997 | 螺紋緊固件.軸向負荷疲勞試驗.試驗方法和試驗結果評定 | Threaded fasteners - Axial load fatigue testing - Test methods and evaluation of results |
| DIN CEN/TS 15087-2006 | 屋頂用已裝粘土和混凝土嵌合瓦片的抗隆起性測定.機械緊固件的試驗方法.德文版本CEN/TS 15087-2005 | Determination of the uplift resistance of installed clay and concrete interlocking tiles for roofing - Test method for mechanical fasteners; German version CEN/TS 15087:2005 |
| DIN EN 10269 Berichtigung 1-2006 | 具有規定高溫和/或低溫性能的緊固件用鋼和鎳合金 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties, German version EN 10269:1999 + A1:2006, Corrigenda to DIN EN 10269:2006-07; German version EN 10269:1999/A1:2006/AC:2006 |
| DIN EN 10269 Berichtigung 2-2007 | 專用高溫和/或低溫性能的緊固件用鋼和鎳合金 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties; German version EN 10269:1999 + A1:2006, Corrigenda to DIN EN 10269:2006-07 |
| DIN EN 10269-2006 | 具有規定高溫和/或低溫性能的緊固件用鋼和鎳合金(包括修改件A1-2006和技術勘誤Ber 1-2006-10 + Ber 2-2007- | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties (includes Amendment A1:2006 and Corrigenda Ber 1:2006-10 + Ber 2:2007-02); English version of DIN EN 10269:2006-07 |
| DIN EN 1075-2000 | 木質構件.試驗方法.金屬板沖壓緊固件連接接頭 | Timber structures - Test methods - Joints made with punched metal plate fasteners; German version EN 1075:1999 |
| DIN EN 12512-2005 | 木結構.試驗方法.機械緊固件接頭的循環試驗 | Timber structures - Test methods - Cyclic testing of joints made with mechanical fasteners; German version EN 12512:2001 + A1:2005 |
| DIN EN 12549-1999 | 聲學.緊固件安裝工具的噪聲測試規范.工程法 | Acoustics - Noise test code for fastener driving tools - Engineering method; German version EN 12549:1999 |
| DIN EN 13271-2004 | 木制緊固件.連接件滑動模數和特性承載力 | Timber fasteners - Characteristic load-carrying capacities and slip-moduli for connector joints; German version EN 13271:2001 + AC:2003 |
| DIN EN 13446-2002 | 木基板材.緊固件拔出能力的測定; 德文版本 EN 13446:2002 | Wood-based panels - Determination of withdrawal capacity of fasteners; German version EN 13446:2002 |
| DIN EN 1382-2000 | 木結構.試驗方法.木制緊固件的抗拔出力.德文版本EN1382-1999 | Timber structures - Test methods - Withdrawel capacity of timber fasteners; German version EN 1382:1999 |
| DIN EN 1383-2000 | 木結構.試驗方法.木制緊固件的楔入阻力 | Timber structures - Test methods - Pull through resistance of timber fasteners; German version EN 1383:1999 |
| DIN EN 1414-2000 | 接觸鎖緊緊固件.后續試驗的循環過程(包括補充件A1,2000) | Touch and close fasteners - Cycling procedure for subsequent testing (includes Amendment A1:2000); German version EN 1414:1996 + A1:2000 |
| DIN EN 14250-2005 | 木制結構.裝配有穿孔金屬板緊固件的預制結構構件的生產要求 | Timber structures - Product requirements for prefabricated structural members assembled with punched metal plate fasteners; German version EN 14250:2004 |
| DIN EN 14831-2005 | 緊固件.上緊性能.扭矩/角度簡化試驗法 | Fasteners - Tightening performance - Torque/Angle simplified test method; German version EN 14831:2005 |
| DIN EN 20225-1992 | 緊固件.螺釘、螺柱和螺母.尺寸符號和標示(ISO 225-83) | Fasteners; bolts, screws, studs and nuts; symbols and designations of dimensioning (ISO 225:1983); german version EN 20225:1991 |
| DIN EN 20273-1992 | 緊固件.螺栓和螺釘?shù)拈g隙孔(ISO 273-1979) | Fasteners; clearance holes for bolts and screws (ISO 273:1979); german version EN 20273:1991 |
| DIN EN 20898-2-1994 | 緊固件的機械性能.第2部分:有規定檢驗載荷值的螺母.粗牙螺紋 | Mechanical properties of fasteners; part 2: nuts with specified proof load values; coarse thread (ISO 898-2:1992); German version EN 20898-2:1993 |
| DIN EN 20898-7-1995 | 緊固件的機械性能.第7部分:公稱直徑為 1 mm - 10 mm 的螺栓和螺釘?shù)呐ちυ囼灪妥钚∨ぞ?(ISO 898-7:1992); | Mechanical properties of fasteners - Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm (ISO 898-7:1992); German version EN 20898-7:1995 |
| DIN EN 26157-1-1991 | 緊固件.表面缺陷.符合一般要求的螺栓、螺釘和螺柱(ISO 6157-1-88) | Fasteners; surface discontinuities; bolts, screws and studs subject to general requirements (ISO 6157-1:1988); german version EN 26157-1:1991 |
| DIN EN 26157-3-1991 | 緊固件.表面缺陷.特殊要求用螺栓、螺釘和螺柱 | Fasteners; surface discontinuities; bolts, screws and studs subject to special requirements (ISO 6157-3:1988); german version EN 26157-3:1991 |
| DIN EN 26891-1991 | 木結構.用機械緊固件進行的連接.測定強度和變形特性的一般原理.(ISO 6891-83) | Timber structures; joints made with mechanical fasteners; general principles for the determination of strength and deformation characteristics (ISO 6891:1983); german version EN 26891:1991 |
| DIN EN 28839-1991 | 緊固件的機械性能.有色金屬制造的螺栓、螺釘、螺柱和螺母 | Mechanical properties of fasteners; nonferrous metal bolts, screws, studs and nuts (ISO 8839:1986); german version EN 28839:1991 |
| DIN EN 28970-1991 | 木結構.用機械緊固件連接的試驗.對木材密度的要求(ISO 8970-88) | Timber structures; testing of joints made with mechanical fasteners; requirements for wood density (ISO 8970:1989); german version EN 28970:1991 |
| DIN EN 383-2007 | 木結構.試驗方法.測定榫型緊固件的嵌入強度和基礎參數 | Timber Structures - Test methods - Determination of embedment strength and foundation values for dowel type fasteners; German version EN 383:2007 |
| DIN EN 4174-2006 | 航天航空系列.陽極電鍍或鉻酸鹽處理鋁合金2024米制系列、連接模壓鎖緊凹頭緊固件 | Aerospace series - Collars, swage locking, sheartype, in aluminium alloy 2024, anodized or chromated, metric series; German and English version EN 4174:2006 |
| DIN EN 50180 Bb.2-2001 | 充油變壓器用1kV-36kV及250A-3.15kA襯套.結構緊固件 | Bushings above 1 kV up to 36 kV and from 250 A to 3,15 kA for liquid filled transformers - Constructional details of fastening |
| DIN EN 792-1-2001 | 手持非電動工具.安全要求.第1部分:非螺紋機械緊固件的裝配動力工具 | Hand-held non-electric power tools - Safety requirements - Part 1: Assembly power tools for non-threaded mechanical fasteners; German version EN 792-1:2000 |
| DIN EN 792-13-2001 | 手持非電動工具.安全性要求.第13部分:緊固件扳擰工具 | Hand-held non electric power tools - Safety requirements - Part 13: Fastener driving tools; German version EN 792-13:2000 |
| DIN EN 792-6-2001 | 手持非電動工具.安全要求.第6部分:螺紋緊固件用裝配動力工具 | Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools for threaded fasteners; German version EN 792-6:2000 |
| DIN EN 912-2001 | 木構件緊固件.木構件的連接件規范（包括勘誤AC-2000) | Timber fasteners - Specifications for connectors for timber (includes corrigendum AC:2000); German version EN 912:1999 + AC:2000 |
| DIN EN ISO 10683-2001 | 緊固件.非電解用鋅片覆層 | Fasteners - Non-electrolytically applied zinc flake coatings (ISO 10683:2000); German version EN ISO 10683:2000 |
| DIN EN ISO 10684-2004 | 緊固件.熱浸鍍鋅涂層 | Fasteners - Hot dip galvanized coatings (ISO 10684:2004); German version EN ISO 10684:2004 |
| DIN EN ISO 10964-1997 | 粘合劑.螺紋緊固件上厭氧粘合劑抗扭強度測定 | Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993); German version EN ISO 10964:1997 |
| DIN EN ISO 1120-2002 | 傳送帶.機械緊固件強度測定.靜態試驗方法 (ISO 1120:2002); 德文版本 EN ISO 1120:2002 | Conveyor belts - Determination of strength of mechanical fastenings - Static test method (ISO 1120:2002); German version EN ISO 1120:2002 |
| DIN EN ISO 12777-1-1996 | 托盤連接件試驗方法.第1部分:托盤用釘子、其它榫釘型緊固件和U形釘?shù)目箯澢鷾y定 | Methods of test for pallet joints - Part 1: Determination of bending resistance of pallet nails, other dowel-type fasteners and staples (ISO 12777-1:1994); German version EN ISO 12777-1:1996 |
| DIN EN ISO 15330-2000 | 緊固件.檢測氫脆用預荷載試驗.平行支承面法 | Fasteners - Preloading test for the detection of hydrogen embrittlement - Parallel bearing surface method (ISO 15330:1999); German version EN ISO 15330:1999 |
| DIN EN ISO 16047-2005 | 緊固件.扭矩/夾持力試驗 | Fasteners - Torque/clamp force testing (ISO 16047:2005); German version EN ISO 16047:2005 |
| DIN EN ISO 16048-2003 | 耐腐蝕不銹鋼緊固件的鈍化處理 | Passivation of corrosion-resistant stainless-steel fasteners (ISO 16048:2003); German version EN ISO 16048:2003 |
| DIN EN ISO 16426-2003 | 緊固件.質量保證體系 | Fasteners - Quality assurance system (ISO 16426:2002); German version EN ISO 14426:2002 |
| DIN EN ISO 3269-2000 | 緊固件.驗收檢查 | Fasteners - Acceptance inspection (ISO 3269:2000); German version EN ISO 3269:2000 |
| DIN EN ISO 3506-1-1998 | 耐蝕鋼緊固件的機械性能.第1部分:螺栓,螺釘和螺柱 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:1997); German version EN ISO 3506-1:1997 |
| DIN EN ISO 3506-2-1998 | 耐蝕鋼緊固件的機械特性.第2部分:螺母 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:1997); German version EN ISO 3506-2:1997 |
| DIN EN ISO 3506-3-1998 | 耐蝕鋼緊固件的機械特性.第3部分:不受拉應力的止動螺釘和類似的緊固件 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:1997); German version EN ISO 3506-3:1997 |
| DIN EN ISO 3506-4-2003 | 耐腐蝕不銹鋼緊固件的機械特性.第4部分:攻絲螺釘 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 4: Tapping screws (ISO 3506-4:2003); German version EN ISO 3506-4:2003 |
| DIN EN ISO 4042-2001 | 緊固件.電鍍層(ISO 4042:1999) | Fasteners - Electroplated coatings (ISO 4042:1999); German version EN ISO 4042:1999 |
| DIN EN ISO 4753-2000 | 緊固件.ISO米制外螺紋零件末端 | Fasteners - Ends of parts with external metric ISO thread (ISO 4753:1999); German version EN ISO 4753:1999 |
| DIN EN ISO 4759-1-2001 | 緊固件公差.第1部分:螺栓、螺釘和墊圈和螺母.產品等級A、B和C | Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts; Product grades A, B and C (ISO 4759-1:2000); German version EN ISO 4759-1:2000 |
| DIN EN ISO 4759-3-2000 | 緊固件公差.第3部分:螺栓、螺釘和螺母用平墊圈.產品等級A和C | Tolerances for fasteners - Part 3: Plain washers for bolts, screws and nuts; product grades A and C (ISO 4759-3:2000); German version EN ISO 4759-3:2000 |
| DIN EN ISO 6157-2-2004 | 緊固件.表面缺陷.第2部分:螺母 | Fasteners - Surface discontinuities - Part 2: Nuts (ISO 6157-2:1995); German version EN ISO 6157-2:2004 |
| DIN EN ISO 898-1-1999 | 碳鋼和合金鋼制緊固件的機械性能.第1部分:螺栓,螺釘和螺柱 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs (ISO 898-1:1999); German version EN ISO 898-1:1999 |
| DIN EN ISO 898-5 Berichtigung 1-2007 | 碳鋼和合金鋼制緊固件機械性能.第5部分:非拉伸應力條件下固定螺釘和類似緊固件 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar fasteners not under tensile stress (ISO 898-5:1998); German version EN ISO 898-5:1998, Corrigenda to DIN EN ISO 898-5:1998-10 |
| DIN EN ISO 898-5-1998 | 碳鋼和合金鋼制緊固件的機械性能.第5部分:非拉伸應力條件下止動螺釘和類似的緊固件 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar fasteners not under tensile stress (ISO 898-5:1998); German version EN ISO 898-5:1998 |
| DIN EN ISO 898-6-1996 | 緊固件機械性能.第6部分:帶規定試驗負荷的螺母.細牙螺紋 | Mechanical properties of fasteners - Part 6: Nuts with specified proof load values; fine pitch thread (ISO 898-6:1994); German version EN ISO 898-6:1995 |
| DIN ISO 1891-1979 | 緊固件.螺栓、螺釘、螺母和附件.術語和名稱 | Fasteners; Bolts, Screws, Nuts and Accessories, Terminology and Nomenclature |
| DIN ISO 272-1979 | 緊固件.六角制件的對邊寬度 | Fasteners; Width across Flats for Hexagon Products |
| DIN ISO 4095-1980 | 航空和航天.宇航結構用緊固件.雙六角(12角)扳手外形 | Aerospace; fasteners for aerospace construction, bi-hexagonal wrenching configuration |
| DIN ISO 5845-1-1997 | 技術圖樣.緊固件組裝簡化表示法.第1部分:一般原理 | Technical drawings - Simplified representation of the assembly of parts with fasteners - Part 1: General principles (ISO 5845-1:1995) |
| DIN ISO 5845-2-1997 | 技術圖樣.緊固件組裝簡化表示法.第2部分:航空航天設備用鉚釘 | Technical drawings - Simplified representation of the assembly of parts with fasteners - Part 2: Rivets for aerospace equipment (ISO 5845-2:1995) |
| DIN ISO 7913-1986 | 航空和航天.緊固件.螺栓和螺釘?shù)男螤詈臀恢霉?等同采用 ISO 7913-1986 | Aerospace; fasteners, tolerances of form and position for bolts and screws; identical with ISO 7913, edition 1985 |
| DIN ISO 8788-1988 | 航空航天.緊固件.螺母的形狀和位置公差 | Aerospace; fasteners; tolerances of form and position for nuts; identical with ISO 8788, edition 1987 |
| DIN ISO 8992-2005 | 緊固件.螺栓、螺釘、螺柱和螺母的一般要求 | Fasteners - General requirements for bolts, screws, studs and nuts (ISO 8992:2005) |
| 編號 | 中文名稱 | 英文名稱
|
|---|
